WE’LL PINPOINT THE HIGH OR LOW WATER PRESSURE ISSUE
When the problem comes from one fixture, then the problem is probably limited to that fixture and is usually simple to solve. Therefore, you should focus your attention and energy on fixing that particular pipe or fixture. In most cases, the problem is mineral deposits caused by our hard water. But substantial water pressure problems that affect the whole house are an indication of something else. Since numerous factors are involved in discovering the low water pressure, pinpointing the exact issue is your first step toward correcting your problem.
LOW WATER PRESSURE COULD BE A PARTIALLY CLOSED WATER METER
Two primary shut-off valves typically control the water supply entering your home. The first shut-off valve is located in front of your house near your street and is a component of your water meter. The primary water supply pipeline from the city that travels to your home is connected to the water meter. You won’t typically use the valve because it’s provided by your municipal water provider and is typically only used by them and their personnel. However, it’s possible that the valve remained partially closed, especially after repairs.
YOUR HOMES SHUT-OFF VALVE MIGHT BE THE ONE TO BLAME
If you just completed plumbing work and might have noticed a decrease in water pressure, the culprit is probably a partially closed shut-off valve. Your home also has a shut-off valve, which often gets located in your garage. In most cases, the shut-off valve is a ball valve with a lever-style handle. However, in certain cases, youngsters playing could partially close it without realizing what it is. It’s also known to partially close when plumbing work was completed on your home.
On the other hand, some shut-off valves resemble wheels and may get opened by rotating them counterclockwise. To ensure enough water is flowing, make certain the valves are fully open. However, if your shut-off valve is a ball valve, then the lever handle would be parallel to the pipe, much like the meter shutdown valve, which may get partially closed after a system repair. So if your water pressure has suddenly dropped following the repair, there is a good chance that the valve is still partially closed.
Plumbing Emergency, call Big B’s Plumbing In Lake Elsinore now!
IF YOU NEVER REPLACED THE PRESSURE REGULATOR, IT’S PROBABLY THE CULPRIT
Another frequent cause of low water pressure in homes is a damaged pressure regulator, commonly referred to as a pressure-reducing valve. Before the water reaches your house, your pressure regulator will regulate the water flow. Your plumbing system and appliances may suffer if the water pressure rises beyond 80 pounds per inch (psi) if not controlled. Set the water pressure regulator to between 40-60 psi. Not every home has a water pressure regulator; however, in the homes that do, a damaged regulator can cause a large rise in your water pressure. When the pressure regulator stops functioning, low water pressure is also conceivable.
YOUR PRESSURE REGULATOR SHOULD GET REPLACED BY A PLUMBING PROFESSIONAL
When the water pressure regulator malfunctions, which can happen suddenly and without warning, all of your home’s appliances could suffer damage if the water pressure accelerates for an extended period. So, replace your regulator if your home gets left with high water pressure. Of course, replacing a pressure regulator should be completed by a plumbing expert. But, if you need high or low water pressure repairs in In Lake Elsinore, California, Big B’s Plumbing is prepared to handle the demand.
BUY A WATER PRESSURE GAUGE TO CHECK YOUR PRESSURE
You may precisely measure the water pressure by mounting a water pressure gauge tester to your outside hose spigot. It’s best to utilize the spigot closest to your pressure regulator for a precise reading. Your suggested household water pressure should be adjusted at 40-60 psi, as was already mentioned. The pressure regulator can be broken if the pressure readings remain abnormally low or high.
Residential plumbing problem? Call an expert at Big B’s Plumbing.
YOUR OLD PIPES COULD BE THE REASON FOR YOUR LOW WATER PRESSURE
The most significant and expensive reason for low water pressure is the deterioration of galvanized steel pipes, which results in highly limited flow rates. These pipelines corrode from the inside out, gradually closing off the water supply. Since this problem progressively deteriorates over many years, you may not notice until you see a sudden drop in pressure. The same can be true for copper piping as well. Hard water deposits can build up over several years, causing your copper pipes to restrict.
Regrettably, a home repipe is the only way to repair outdated galvanized steel pipes. The preferred plumbing material for house repipes nowadays, Cross-linked Polyethylene (PEX) tubing; while some homeowners still like copper, Big B’s Plumbing has experts in both PEX and copper. So if you’re a Lake Elsinore, California resident with high or low water pressure, call today; we have you covered.
WHY USE BIG B’S PLUMBING?
- Five stars on Facebook
- Better Business Bureau A+ Rating
- Licensed Plumbing Contractor in California
- Google My Business Customer-Reviews 4.9
- All Our Plumbers Have Received Background Checks
Call today and get the service you deserve!
